- Exports to Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — based in China, serving customers worldwide.
- Dongguan Zhuohang Ltd (Registration No. 91441900MA4UWT6X39), operating as Zhuohang Precision Machining Factory, established 2005.
- Who is legally and financially on the other side of the purchase order, The failure mode is not fraud — it is the middleman's margin on information.
- Build-to-print: the plant cuts to your drawing and reports against it.
Why the word "company" carries no information on its own
A company description that cannot name its registration number, its floor area, and its staff count is a description of a website, not of a business. The three facts are cheap to publish and expensive to fake.
The failure mode is not fraud — it is the middleman's margin on information. When something goes wrong on the floor, the person who knows what happened is two steps away from the person who can authorise a fix.
The practical test is whether the description could be false. Established in 2005 with 100 machines is checkable; a professional and reliable partner is not. Prefer the description that could be disproved.
Tolerance, and the instrument behind it
Milling and turning hold ±0.002 mm (turning) / ±0.003 mm (milling); precision grinding and wire EDM hold ±0.002 mm. A tolerance is only worth as much as the instrument that verifies it, so the floor runs 20+ inspection instruments alongside the machines. CMM for dimensional and true position, vision and profile instruments for surface and geometry, hardness testers and coating gauges for heat treatment and plating, and XRF for incoming material composition against the mill certificate.
The rule that matters on a drawing is that a tolerance is held by the process, not by the machine. Where a feature is tight, the finishing pass is separated from roughing, the part is allowed to stabilise, and the measurement is taken at a controlled temperature — a part measured warm is not the part the customer receives.
Where the money is actually decided
What makes a quote accurate is a complete drawing: a 3D model for geometry, a 2D drawing for tolerances, a grade rather than a material family, and a quantity with the expected repeat quantity stated separately. The absence of any one of these is what turns a quote into an estimate.
This is cheaper to settle at quote time than once parts already exist, because the changes are usually trivial on the drawing and significant on the machine.
Which entity is responsible for the work?
Dongguan Zhuohang Ltd, Registration No. 91441900MA4UWT6X39, in operation since 2005.
How the production floor is organised
Capacity is depth, not a headline machine. The table below is the routing map: each family has a lane, and the depth in each lane is what keeps a part out of someone else's queue.
| Machine family | Count | Representative models | Role in the schedule |
|---|---|---|---|
| 3-axis vertical machining | 50+ centres | Brother SPEEDIO S500Z2N / S700Z2N | Prismatic work at the lowest cost per part |
| 4-axis machining | 20+ centres | Mazak VCE-430AL / VCE-570CL | Indexed multi-face parts without re-fixturing |
| 5-axis machining | 20+ centres | Mazak VARIAXIS i series | Single-setup complex geometry |
| 5-axis mill-turn | — | Mazak INTEGREX i-H series | Turned and milled features in one clamping |
| CNC turning / mill-turn | 25+ lathes | Mazak QT-COMPACT 200MSY L | Round parts, live tooling |
| Swiss-type turning | — | Citizen Cincom A20 / Star SR-32JII / Tsugami B0205 | Long, slender parts at high L/D ratios |
| Precision grinding | 7+ grinders | — | Final tolerance on bearing seats and roundness-critical faces |
| Wire EDM | — | Sodick | Sharp internal corners and hardened material |
What to read out of this list: a part does not wait behind a single machine. Depth in the same family is what lets work re-route rather than queue, and it is what makes a prototype ramp to production on the same floor.
What is the certification position?
ISO 9001:2015, IATF 16949:2016 (excluding clause 8.3 product design), and ISO 14001:2015, each with a certificate number verifiable with the registrar.
Four checks to run on any CNC lathe machining quote
Whether you buy from this plant or another, these checks separate a real floor from a brochure. None of them require a purchase order.
- Registered entity name and number? Ask for it in writing.
- Production address that matches the registered address? Ask for it in writing.
- Staff count and shift structure? Ask for it in writing.
- Named contact who is accountable? Ask for it in writing.
What happens between quote and first article?
Programming and offline verification, fixture design and build, material inward inspection, roughing, finishing, inspection, and the first-article report. Each stage has a way to fail, and the fixes that hurt most are the first and last steps. The manufacturability review is where cost is actually decided. A pocket depth reduced by a few millimetres, or an internal corner radius opened from 1 mm to 3 mm, cuts cycle time more than any change of machine, because it changes the tool that can be used.
How to verify the shop, not just the quote
Beyond the price, you should check three things. The entity - who you are actually contracting with, because the legal entity and the marketing name are not always the same. The certificates - whether the ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015 numbers are published and verifiable, not asserted. And the floor - whether the machines and the inspection actually exist, because a shop that cannot show a Hexagon CMM report cannot honestly claim a tight tolerance. This floor is Dongguan Zhuohang Ltd, 6,800 m² in Hengli Town, Dongguan, with 100+ CNC machines and the certificate numbers published.
The questions that separate a real shop from a broker
Ask three questions and listen to the answers. What machines run this part, and how many? A real shop names models - Mazak VARIAXIS I-600, INTEGREX I-250H S, Brother SPEEDIO, TSUGAMI and CITIZEN Swiss lathes. How do you verify a tight tolerance? A real shop points at the Hexagon CMM and the 10:1 gauge rule. Who is responsible if a batch is wrong? A real shop names the entity and stands behind it. Contact Felipe Iglesias at [email protected] or +86 13126536955 and ask those three questions before you place the order.
How to verify the claim in one email
The fastest way to separate a real floor from a brochure is to ask for the machine list and the certificate numbers - and this facility answers in one email. Dongguan Zhuohang Ltd operates 100+ CNC machines across 6,800 m² in Hengli Town, Dongguan: Mazak VARIAXIS I-600 five-axis, INTEGREX I-250H S mill-turn, Brother SPEEDIO, and TSUGAMI, STAR and CITIZEN Swiss lathes. Inspection is on a Hexagon CMM with the 10:1 gauge rule, certification is to ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015, and critical characteristics run at Ppk 1.67 initial and Cpk 1.33 in production.
Worldwide buyers across Europe, the Americas, Asia, Oceania and Africa are supplied from Dongguan. MOQ is 1 piece, lead times run roughly 3 / 7 / 30 days, and the quote from Felipe Iglesias ([email protected], +86 13126536955) comes back with the routing and the capability evidence together.
Take the next step
One drawing and one quantity is the whole hand-off. Send a STEP or IGES model and a 2D drawing with the tolerances, datums, material grade and finish, state the quantity and lead time, and the reply is an itemised quote - material, setup, cycle time, inspection - rather than a round number. If the drawing is incomplete, send what you have and the open questions; the point is to open the conversation, not to wait for a perfect package.
Contact Felipe Iglesias at [email protected] or +86 13126536955. MOQ is 1 piece, lead times run about 3 / 7 / 30 days, and the service area covers Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa, shipped worldwide from Dongguan.
Tolerance and surface finish reference
±0.003 mm milled, ±0.002 mm turned, and ±0.002 mm ground or wire-cut, all verified on a Hexagon CMM against the datum scheme. Surface finishes span Ra 0.8 to 3.2 µm as-milled, Ra 0.2 to 0.4 µm ground, and Ra 0.05 to 0.1 µm polished. The 10:1 gauge rule governs every feature - the instrument must resolve ten times finer than the tolerance it checks. And the datum is what makes the tolerance real: read against two different datums, the same callout gives two different parts, so state the datum and the convention, ASME Y14.5 or ISO.
What this shop actually runs
Capability evidence should come as specifics, not slogans. Behind this guide is a 6,800 m2 plant in Dongguan, China running 100+ CNC machines with 100+ staff. The machine list by category:
- 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Intended for compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
- 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Intended for prismatic parts, plates, brackets, housings.
- Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Intended for long, slender rotational parts at ±0.002 mm.
- CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Intended for shafts, bushings, flanges up to ±0.002 mm.
- Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Intended for hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
- Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
- Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.
Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.
Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.
Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.
Contact: Felipe Iglesias, [email protected], +86 13126536955.
Ask the four questions before you commit
Registration number, machine depth, certificate numbers, and a walk of the floor. Contact Felipe Iglesias at [email protected] or +86 13126536955 — on-site and video audits are welcome.
Frequently Asked Questions
Is your IATF 16949 certificate valid for design work?
No. The certificate excludes clause 8.3 (product design). The plant is certified to manufacture to your design and to run the associated process controls, not to originate product design.
What files do you need for a quote?
In short, A 3D model (STEP or IGES) with a 2D drawing carrying the tolerances, surface finish callouts, material spec and any inspection or certification requirements. The drawing defines the contract — the model alone usually leaves the tolerance scheme unspecified.
How quickly can you quote cnc lathe machining?
Quotes are returned with a manufacturability read rather than a price alone — where a tolerance or a feature will drive cost, that is flagged at quote stage rather than after the first article. Turnaround depends on drawing completeness.
How is an engineering change handled mid-production?
The change is documented against a revision, the affected parts in process are identified, and the revised drawing is confirmed in writing before work restarts. The important part is that the revision in force at any moment is a single, written one.
How is material traceability maintained?
Incoming stock is checked against the mill certificate — composition by XRF, hardness where specified — and traceability is held per heat or per batch as the certificate defines it.
Are you a manufacturer or a trading company?
A manufacturer. The legal entity is Dongguan Zhuohang Ltd (Registration No. 91441900MA4UWT6X39), operating a 6,800 m² facility with a hundred-odd machines and 100+ staff in Dongguan. Factory visits are welcome.
What materials do you machine?
Aluminum, stainless steel, titanium, brass, copper, and Inconel for metals; PEEK and Delrin (POM) for plastics. Material certificates are verified on incoming stock.
Continue reading: 3 Axis CNC Lathe Machining · 4 Axis CNC Lathe Machining · 5 Axis CNC Lathe Machining
Standards referenced on this page
- ASTM A582/A582M-12 — Standard Specification for Free-Machining Stainless Steel Bars
- ASTM B348/B348M-21 — Standard Specification for Titanium and Titanium Alloy Bars and Billets
- ISO 9001 — Quality management systems — Requirements